Home > Products

Standard Non-standard Static and Dynamic Seal NBRHNBRSiliconeFPM Rubber O Ring

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Differences between Static and Dynamic O-rings

    Dynamic O-rings require more lubrication than static ones. Depending on the application, static or dynamic seals will be used. O-rings are useful in a varied number of industries and applications. They are effective across a wide range of temperatures and pressures. However, using the right O-ring for each application will help you increase the ...

    Get Price
  • Groove Design: O-Ring Seals - Minnesota Rubber &

    Groove Design: O-Ring Seals for Static and Non-Rotary Dynamic Applications. Cross-section. Select an O-Ring cross-section size from the available standard sizes. If you are unsure what cross-section size to use, see here. Clearance. Determine the maximum clearance present in your application.

    Get Price
  • What are Static Seals? | Hot Topics - Apple Rubber

    2018-2-6 · The o-ring is permanently deformed and considered non-reusable. A Dovetail provides a retaining feature in a face seal gland. If the groove design in illustration 4.5 was of a standard face seal, the o-ring would fall out as the valve cycles up. The dovetail retains the o-ring in the groove. The o-ring is forced into the dovetail on ...

    Get Price
  • Section V – Dynamic O-Ring Sealing

    2010-1-6 · Dynamic O-Ring Sealing 5.1 Introduction Dynamic O-ring sealing applications are considerably more involved than static applications due to the implied motion against the O-ring seal interface. Resistance to fl uids must be more carefully scrutinized than in conventional static seal designs since a volumetric increase in the O-ring in excess of ...

    Get Price
  • What you Need to Know About Dynamic Seal

    2018-11-26 · Dynamic Seals O-Ring. An O-Ring is the most widely used type of seal. The round cross-section is economical to produce and provides a bi-directional seal that is easy to install. When applied correctly the O-Ring will function well in most dynamic applications.

    Get Price
  • Parker O-Ring Handbook

    2007-8-28 · seal assembly consists of an elastomer O-ring and a gland. An O-ring is a circular cross-section ring molded from rubber (Figure 1-1). The gland — usually cut into metal or another rigid material — contains and supports the O-ring (Figures 1-2 and 1-3). The combination of these two elements; O-ring and gland — constitute the classic O ...

    Get Price
  • O Ring Seals, O-Rings, and O Ring Suppliers - Zycon

    An O ring is a torus or donut-shaped mechanical seal used to prevent the flow or leakage of fluids between two mating surfaces. Produced from different natural and synthetic elastomers, including Buna-N, Viton®, and silicone rubber, O-rings have circular cross sections.

    Get Price
  • ERIKS - Technical Manual - O-Ring Gland Design

    2006-10-31 · 1. Male or Plug - the O-ring groove is located on a plug which is inserted into the housing or cylinder (fig. 1-23) 2. Female or Tube - the O-ring groove is located in the housing or cylinder and a tube is installed through the O-ring l.D. (fig. 1-24). Male or Plug Seal design is based on the following factors (refer to fig. 1-23). Bore ...

    Get Price
  • Square-Profile O-Rings - The O-ring Store

    Standard AS-568 size Rubber Square Rings can sometimes be used interchangeably in AS-568 standard size O-Ring gland designs. Square Rings can be used in static applications where high sealing load force is required or when the sealing area is too thin to accommodate anything else. In most static applications, it is a direct replacement for an O-ring and generally will perform a high pressure ...

    Get Price
  • O-Rings - Standard AS568, ISO 3601 | Apple Rubber

    O-Ring Sizing Guides. For standard sizes, aerospace standard AS568 and ISO 3601 for metric sizes are used to give the dimension and tolerance. These are the sizes that are most readily available. Since new designs should also try to incorporate these sizes, we offer groove design tools for static and dynamic applications. AS568 Standard O-Ring ...

    Get Price